Network Working Group O. Gsenger Internet-Draft May 6, 2008 Expires: November 7, 2008 secure anycast tunneling protocol (SATP) draft-gsenger-secure-anycast-tunneling-protocol-02 Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on November 7, 2008. Copyright Notice Copyright (C) The IETF Trust (2008). Gsenger Expires November 7, 2008 [Page 1] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 Abstract The secure anycast tunneling protocol (SATP) defines a protocol used for communication between any combination of unicast and anycast tunnel endpoints. It allows tunneling of every ETHER TYPE protocol (ethernet, ip ...). SATP directly includes cryptography and message authentication based on the methods used by the Secure Real-time Transport Protocol(SRTP) [1]. It can be used as an encrypted alternative to IP Encapsulation within IP [3] and Generic Routing Encapsulation (GRE) [4]. Both anycast receivers and senders are supported. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. Notational Conventions . . . . . . . . . . . . . . . . . . 3 2. Motivation and usage scenarios . . . . . . . . . . . . . . . . 4 2.1. Usage scenarions . . . . . . . . . . . . . . . . . . . . . 4 2.1.1. Tunneling from unicast hosts over anycast routers to other unicast hosts . . . . . . . . . . . . . . . . 4 2.1.2. Tunneling from unicast hosts to anycast networks . . . 5 2.1.3. Redundant tunnel connection of 2 networks . . . . . . 5 2.2. Encapsulation . . . . . . . . . . . . . . . . . . . . . . 6 3. Using SATP on top of IP . . . . . . . . . . . . . . . . . . . 8 3.1. Fragmentation . . . . . . . . . . . . . . . . . . . . . . 8 3.2. ICMP messages . . . . . . . . . . . . . . . . . . . . . . 8 4. Protocol specification . . . . . . . . . . . . . . . . . . . . 9 4.1. Header format . . . . . . . . . . . . . . . . . . . . . . 9 4.2. sequence number . . . . . . . . . . . . . . . . . . . . . 9 4.3. sender ID . . . . . . . . . . . . . . . . . . . . . . . . 9 4.4. MUX . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.5. payload type . . . . . . . . . . . . . . . . . . . . . . . 10 4.6. payload . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.7. padding (OPTIONAL) . . . . . . . . . . . . . . . . . . . . 10 4.8. padding count (OPTIONAL) . . . . . . . . . . . . . . . . . 10 4.9. MKI (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . 10 4.10. authentication tag (RECOMMENDED) . . . . . . . . . . . . . 10 4.11. Encryption . . . . . . . . . . . . . . . . . . . . . . . . 11 5. Security Considerations . . . . . . . . . . . . . . . . . . . 12 5.1. Replay protection . . . . . . . . . . . . . . . . . . . . 12 6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 13 7. References . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7.1. Normative References . . . . . . . . . . . . . . . . . . . 14 7.2. Informational References . . . . . . . . . . . . . . . . . 14 Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 16 Intellectual Property and Copyright Statements . . . . . . . . . . 17 Gsenger Expires November 7, 2008 [Page 2] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 1. Introduction SATP is a mixture of a generic encapsulation protocol like GRE [4] and a secure tunneling protocol as IPsec [5] in tunnel mode. It can be used to build redundant virtual private network (VPN) connections. It supports peer-to-peer tunnels, where tunnel endpoints can be any combination of unicast, multicast or anycast hosts, so it defines a Host Anycast Service [6]. Encryption is done per packet, so the protocol is robust against packet loss and routing changes. To reduce header overhead ncryption techniques of SRTP [1] are being used. 1.1. Notational Conventions The keywords "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC2119 [2]. Gsenger Expires November 7, 2008 [Page 3] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 2. Motivation and usage scenarios This section gives an overview of possible usage scenarios. Please note that the protocols used in the figures are only examples and that SATP itself does not care about either transport protocols or encapsulated protocols. Routing is not done by SATP and each implemetation MAY choose it's own way of doing this task (e.g. using functions provided by the operating system). SATP is used only to encapsulate and encrypt data. 2.1. Usage scenarions 2.1.1. Tunneling from unicast hosts over anycast routers to other unicast hosts An example of SATP used to tunnel in a unicast client - anycast server model --------- router ----------- / \ unicast ------+---------- router ------------+------ unicast host \ / host --------- router ----------- unicast | encrypted | anycast | encrypted | unicast tunnel | communication | tunnel | communication | tunnel endpoint | using SATP | endpoint | using SATP | endpoint Figure 1 In this scenario the payload is encapsuleted into a SATP packet by a unicast host and gets transmitted to one of the anycast routers. After transmisson the packet gets decapsulated by the router. This router makes a routing descision based on the underlying protocol and transmits a new SATP package to one or more unicast hosts depending on this decision. Gsenger Expires November 7, 2008 [Page 4] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 2.1.2. Tunneling from unicast hosts to anycast networks An example of SATP used to encrypt data between a unicast host and anycast networks -------Router -+---- DNS Server / \ / --- 6to4 Router / unicast -------+----------Router --+--- DNS Server host \ \ \ --- 6to4 Router \ -------Router -+---- DNS Server \ --- 6to4 Router unicast | encrypted | anycast | plaintext tunnel | communication | tunnel | anycast endpoint | using SATP | endpoint | services Figure 2 When the unicast hosts wants to transmit data to one of the anycast DNS servers, it encapsulates the data and sends a SATP packet to the anycast address of the routers. The packet arrives at one of the routers, gets decapsulated and is then forwarded to the DNS server. This method can be used to tunnel between clients and networks providing anycast services. It can also be used the other way to virtually locate a unicast service within anycasted networks. 2.1.3. Redundant tunnel connection of 2 networks An example of SATP used to connect 2 networks Router ----------- ---------------Router / \ / \ Network - Router ------------x Network A \ / \ / B Router ----------- ---------------Router | packets | packets | packets | plaintext | get | take a | get | plaintext packets | de/encrypted | random | de/encrypted | packets |de/encapsulated| path |de/encapsulated| Gsenger Expires November 7, 2008 [Page 5] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 Figure 3 Network A has multiple routers which act as gateway/tunnel endpoints to another network B. This way a redundant encrypted tunnel connection between the two networks is built up. All tunnel endpoints of network A share the same anycast address and all tunnel endpoints of network B share another anycast address. When a packet from network A is transmitted to network B, it first arrives on one of network A's border routers. Which router is used is determined by network A's internal routing. This router encapsulates the package and sends it to the anycast address of network B's routers. After arrival the SATP packet gets decapsulated and routed to its destination within network B. 2.2. Encapsulation SATP does not depend on which lower layer protocol is used. This section only gives an example of how packets could look like. Gsenger Expires November 7, 2008 [Page 6] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 Examples of SATP used with different lower layer and payload protocols +------+-----+-------------------------------+ | | | +----------------+-----+ | | IPv6 | UDP | SATP | Ethernet 802.3 | ... | | | | | +----------------+-----+ | +------+-----+-------------------------------+ Tunneling of Ethernet over UDP/IPv6 +------+-----+---------------------------+ | | | +------+-----+-----+ | | IPv4 | UDP | SATP | IPv6 | UDP | RTP | | | | | +------+-----+-----+ | +------+-----+---------------------------+ Tunneling of IPv6 over UDP/IPv4 with RTP payload +------+-------------------------------+ | | +----------------+-----+ | | IPv6 | SATP | Ethernet 802.3 | ... | | | | +----------------+-----+ | +------+-------------------------------+ Tunneling of Ethernet over IPv6 +------+---------------------------+ | | +------+-----+-----+ | | IPv4 | SATP | IPv6 | UDP | RTP | | | | +------+-----+-----+ | +------+---------------------------+ Tunneling of IPv6 over IPv4 with RTP payload Figure 4 Gsenger Expires November 7, 2008 [Page 7] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 3. Using SATP on top of IP 3.1. Fragmentation The only way of fully supporting fragmentation would be to synchronise fragments between all anycast servers. This is considered to be too much overhead, so there are two non-perfect solutions for these problems. Either fragmentation HAS TO be disabled or if not all fragments arrive at the same server the IP datagramm HAS TO be discarded. As routing changes are not expected to occur very frequently, the encapsulated protocol can do a retransmission and all fragments will arrive at the new server. If the payload type is IP and the IP headers' Don't Fragment (DF) bit is set, then the DF bit of the outer IP header HAS TO be set as well. 3.2. ICMP messages ICMP messages MUST be relayed according to rfc2003 section 4 [3]. This is needed for path MTU detection. Gsenger Expires November 7, 2008 [Page 8] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 4. Protocol specification 4.1. Header format Protocol Format 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | sequence number | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | sender ID | MUX | | +#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+ | | | payload type | | | | +-------------------------------+ | | | | .... payload ... | | | | +-------------------------------+ | | | | padding (OPT) | pad count(OPT)| | +#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+#+-+ | ~ MKI (OPTIONAL) ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | : authentication tag (RECOMMENDED) : | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | +- Encrypted Portion Authenticated Portion ---+ Figure 5 4.2. sequence number The sequence number is a 32 bit unsigned integer in network byte order. It starts with a random value and is increased by 1 for every sent packet. After the maximum value it starts over from 0. This overrun causes the ROC to be increased. 4.3. sender ID The sender ID is a 16 bit unsigned integer. It HAS TO be unique for every sender sharing the same anycast address. 4.4. MUX The MUX (multiplex) field is a 16 bit unsigned integer. It is used to distinguish multiple tunnel connections. Gsenger Expires November 7, 2008 [Page 9] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 4.5. payload type The payload type field defines the payload protocol. ETHER TYPE protocol numbers are used. See IANA assigned ethernet numbers [7] . The values 0000-05DC are reserverd and MUST NOT be used. Some examples for protocol numbers HEX 0000 Reserved .... Reserved 05DC Reserved 0800 Internet IP (IPv4) 6558 transparent ethernet bridging 86DD IPv6 Figure 6 4.6. payload A packet of type payload type (e.g. an IP packet). 4.7. padding (OPTIONAL) Padding of max 255 octets. None of the pre-defined encryption transforms uses any padding; for these, the plaintext and encrypted payload sizes match exactly. Transforms are based on transforms of the SRTP protocol and therefore might use the RTP padding format, so a RTP-like padding is supported. If the padding count field is present, the padding count field MUST be set to the padding length. 4.8. padding count (OPTIONAL) The number of octets of the padding field. This field is optional. Its presence is signaled by the key management and not by this protocol. If this field isn't present, the padding field MUST NOT be present as well. 4.9. MKI (OPTIONAL) The MKI (Master Key Identifier) is OPTIONAL and of configurable length. See SRTP Section 3.1 [1] for details. 4.10. authentication tag (RECOMMENDED) The authentication tag is RECOMMENDED and of configurable length. It contains a cryptographic checksum of the sender ID, sequence number and the encrypted portion, but not of the MKI. On transmitter side Gsenger Expires November 7, 2008 [Page 10] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 encryption HAS TO be done before calculating the authentication tag. A receiver HAS TO calculate the authentication tag before decrypting the encrypted portion. 4.11. Encryption Encryption is done in the same way as for SRTP [1]. This section will only discuss some small changes that HAVE TO be made. Please read SRTP RFC3711 section 3-9 [1] for details. The least significant bits of SSRC are replaced by the sender ID and the most significant bits are replaced by the MUX. For the SRTP SEQ the 16 least significant bits of the SATP sequence number are used and the 16 most significant bits of the sequence number replace the 16 least significant bits of the SRTP ROC. Difference between SRTP and SATP 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SATP sequence number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ = +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SRTP ROC least significant | SRTP SEQ | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SATP MUX | SATP sender ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ = +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SRTP SSRC | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 7 Gsenger Expires November 7, 2008 [Page 11] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 5. Security Considerations As SATP uses the same encryption techniques as SRTP [1], it shares the same security issues. This section will only discuss some small changes. Please read SRTP RFC3711 section 9 [1] for details. 5.1. Replay protection Replay protection is done by a replay list. Every anycast receiver has its own replay list, which SHOULDN'T be syncronised because of massive overhead. This leads to an additional possible attack. An attacker is able to replay a captured packet once to every anycast receiver. This attack is considered be very unlikely because multiple attack hosts in different locations are needed to reach seperate anycast receivers and the number of replays is limited to count of receivers - 1. Such replays might also happen because of routing problems, so a payload protocol HAS TO be robust against a small number of duplicated packages. The window size and position HAS TO be syncronised between multiple anycast receivers to limit this attack. Gsenger Expires November 7, 2008 [Page 12] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 6. IANA Considerations The protocol is intended to be used on top of IP or on top of UDP (to be compatible with NAT routers), so UDP and IP protocol numbers have to be assiged by IANA. Gsenger Expires November 7, 2008 [Page 13] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 7. References 7.1. Normative References [1] Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K. Norrman, "The Secure Real-time Transport Protocol (SRTP)", RFC 3711, March 2004. [2] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [3] Perkins, C., "IP Encapsulation within IP", RFC 2003, October 1996. 7.2. Informational References [4] Farinacci, D., Li, T., Hanks, S., Meyer, D., and P. Traina, "Generic Routing Encapsulation (GRE)", RFC 2784, March 2000. [5] Kent, S. and R. Atkinson, "Security Architecture for the Internet Protocol", RFC 2401, November 1998. [6] Partridge, C., Mendez, T., and W. Milliken, "Host Anycasting Service", RFC 1546, November 1993. Gsenger Expires November 7, 2008 [Page 14] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 URIs [7] Gsenger Expires November 7, 2008 [Page 15] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 Author's Address Othmar Gsenger Puerstingerstr 32 Saalfelden 5760 AT Phone: Email: satp@gsenger.com URI: http://www.gsenger.com/satp/ Gsenger Expires November 7, 2008 [Page 16] Internet-Draft secure anycast tunneling protocol (SATP) May 2008 Full Copyright Statement Copyright (C) The IETF Trust (2008). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgment Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Gsenger Expires November 7, 2008 [Page 17]